Skip to main content

Electrical Service Panel

 

Electrical Service Panel

Every home has a service panel that distributes electricity to switches, outlets, and appliances. The service panel is usually found in the basement, garage, or utility area.

When a short or overload shuts down power to a circuit, this is where you can restore the flow. It is also where you will shut down power to a circuit before starting a project or repair.

Fuses and Circuit Breakers

All service panels are equipped with fuses or circuit breakers that protect the wires in each circuit from overheating and causing a fire. In general, older service panels use fuses, while more modern systems rely on circuit breakers.

Fuses and circuit breakers are safety devices that help prevent overloading of your home electrical system and prevent fires. They stop the electrical current if it exceeds the safe level for some portion of your home electrical system.

Fuses

Service panels installed before 1965 use fuses to protect each individual circuit. Early fuses were commonly used in 30- and 60-amp service panels. Today, new homes require 100- to 200-amp service panels in order to provide proper protection.

There are several different types of fuses, and picking the right one may seem confusing at first. Each fuse is marked with a code, which provides information about the type of base and the degree of time delay, if any.

Instructions for Replacing Fuses:

Once a fuse is blown, it must be unscrewed and thrown away. When replacing fuses in your service panel:

  • Always make sure that the replacement fuse matches the amperage rating of the circuit.
  • Never replace a fuse with one that has a larger amperage rating. This is a very dangerous practice and a serious fire hazard.






 

Comments

Post a Comment

Popular posts from this blog

Home Wiring System

  Home Wiring System More than 30 million homes, or about one-third of the homes in the United States are at least 50 years old, and studies have shown that the frequency of fires in these aging homes is disproportionately high. Many older homes were built with electrical systems and components which are no longer safe and may be considered as fire hazards. Fire and other electrical safety concerns may arise due to aging, improper installation and alteration, or misuse. It is important to identify what type, color, and size wire is needed in order to properly address hazardous situations before they become critical. Knob & Tube Wiring: 1800s–1930s Knob and tube wiring was designed as an open air system that used ceramic knobs to separate wires from combustible framing. These suspended wires were directed through ceramic tubes to prevent contact with the wood framing and starting a fire. Today, knob and tube wiring is considered a fire hazard because it is not a grounded system,...
Post a Comment
Read more

Ground Fault Circuit Interrupters: What if GFCIs Did Not Exist?

  Ground Fault Circuit Interrupters (GFCI) were first introduced in the bathrooms of homes as required by the 1975 edition of the National Electrical Code. Prior to 1975, only outdoor receptacles and receptacles near swimming pools require GFCI protection. Since then, GFCI requirements grew as in-home electricity use and the amount of potential contact with water and electricity in homes increase.  In the ten years between 1971 and 1980, there was an estimated average of 1,101 electrocutions in the United States, including 491 consumer product electrocutions every year. As GFCI requirements expanded, the number of electrocutions dropped significantly. Between 2011 and 2022, there was an estimated average of 246 electrocutions and year, including 41 consumer product electrocutions.  GFCI Facts 80% drop in electrocutions since the introduction of GFCI protection in bathrooms in 1975 93% drop in consumer product electrocutions between 1975 and 2020 Since 1978, the median yea...
Post a Comment
Read more

Reaching to Safety: Use Extension Cords Properly

  Roughly 3,300 home fires originate in extension cords each year, killing 50 people and injuring 270 more. Extension cords can overheat and cause fires when used improperly, so keep these important tips in mind to protect your home and workplace. Don’t attempt to plug extension cords into one another Make sure extension cords are properly rated for their intended use, indoor or outdoor, and meet or exceed the power needs of the device being used Keep all outdoor extension cords clear of snow and standing water Do NOT overload extension cords Heavy reliance on extension cords is an indication that you have too few outlets to address your needs. Have additional outlets installed where you need them Inspect cords for damage before use. Check for cracked or frayed sockets, loose or bare wires, and loose connections Do NOT nail or staple extension cords to walls or baseboards Do NOT run extension cords through walls, doorways, ceilings, or floors. If a cord is covered, heat canno...
Post a Comment
Read more